Introduction
InstantBlue™ is a ready-to-use Coomassie® patented colourant that is specially formulated for ultra-fast, sensitive and safe detection of your protein gels and can be stained in minutes without the need for wash, fixing or bleaching. Only proteins stain resulting in well-defined blue bands on a very transparent background. Background reduction interference results in a better signal-to-noise ratio and can also have a positive impact on overall resolution and sensitivity. InstantBlue’s formula is non-toxic and does not contain any methanol. Proteins stained with the InstantBlue stain are also compatible with mass spectrometry (MS) analysis.
Content
1L of reagent, containing Coomassie stain, ethanol, phosphoric acid and solubilizing agents in water. (Caution: phosphoric acid is a corrosive liquid.)
Storage
Upon receipt store at + 4°C. Discard any reagent that shows discolouration or evidence of microbial contamination. Be sure to keep capped bottle when not in use
Recommended Protocol And Notes for Use
Before use: mix InstantBlue solution immediately before use by gently inverting the bottle several times (do not shake the bottle to mix the solution).
Important
1. Multiple washes before staining with InstantBlue are NOT required or recommended.
2. One alcohol/acetic acid fixation step prior to staining with InstantBlue is NOT required or recommended.
3. NO post-stain decolourization step is required or recommended with InstantBlue.
Standard Protocol
- After electrophoresis, remove the gel from the tank and transfer it directly to the InstantBlue staining solution. Make sure the gel moves freely on the stain to facilitate spreading. Typically ~20 mL is needed to cover the gel.
- Coloured protein bands will begin to develop immediately, and adequate intensity is typically achieved after 15 minute incubation at room temperature with a mild shake.
- Photograph your gel when the required intensity has been reached accomplished. The gels can be kept in the staining solution, but be sure to that the gel is covered with liquid. Close the container to reduce InstantBlue evaporation. Alternatively, the gel can be stored in ultrapure water after staining for 1 hour in Instant Blue.
- After use, the staining solution should be discarded and it cannot be reused. InstantBlue is provided ready to a use solution and should not be diluted.
Protocol For Drying The Gel:
1. Make sure the gel has been stained for at least 1 hour. Although the protein bands will be visible after a few minutes from incubation to staining, the staining process is usually completed after 1 h of incubation. Depending on the type of gel you are using, longer incubation may be required. Additional processing of the gel before completing the staining process can result in the discolouration of proteins and reduced sensitivity. If this occurs, simply re-stain the gel incubating overnight in InstantBlue.
2. Immerse the gel in approximately 100 ml of ultrapure water at ~70°C (heat for the 30s to 60s in a microwave oven). Incubate for at least 1 hour while gently rocking. Optionally sorbent paper or paper towel may be added. The gels can be incubated overnight in water.
3. Incubate the gel in a “gel drying solution” (for example, 4% glycerol, 20% ethanol in water) for 2 min. incubation of any Coomassie® stained gel in an alcohol solution will eventually result in discolouration of the bands, so avoid
incubation for more than 5 min.
4. The gel is now ready to dry between moistened cellophane membranes
Protocol For The Destination Of Protein Bands For MS Analysis
- Excise the protein band of interest and transfer it to a clean place Eppendorf tube.
- Add 1 ml of 30% ethanol or 30% acetone or 30% acetic acid (Note: acetic acid can result in acetylation of the N-terminus.)
- Incubate for 20 min (incubate at 60°C – 70°C to increase the fade rate).
- Decant the supernatant and repeat steps 2 and 3 at least 3 times or until the gel is transparent.
